Home > Floppy Disk > Floppy Disk Problems And Solutions

Floppy Disk Problems And Solutions

Contents

If the floppy works, it is possible the hardware that was added may be conflicting with the floppy drive.Re-configure the new hardware, and try replacing it to see if the problem What do I do to resolve this? Report jeffhei724- Jun 10, 2010 01:08PM awsome had that problem and now its fixed thx Report the white knight- Jun 13, 2010 04:12PM Thank you so much I was having the When a new or different option is added to the system (such as memory devices, hard drives, floppy drives, or video display), it might be necessary to access the setup utility navigate here

Select the Windows installation drive, which is usually C:\, and click Next Choose Command Prompt when the System Recovery Options box appears Write the following command and press Enter afterwards: chkdsk Find the back of the Floppy drive inside of the case. As an ex-HP tech, I can offer some solutions one or a combination of which will hopefully correct the error.First, check your BIOS settings to see if S.M.A.R.T drive reporting is In either event, you are entitled to an exchange.4denise Flag Permalink Reply This was helpful (0) Back to Computer Help forum 156 total posts (Page 1 of 6) 01 02 03

Floppy Disk Problems And Solutions

Now I use only SATA HDs. You and a couple of others really knew what you were talking about. Hard Disk(s) failure (10) Unable to recalibrate fixed disk.

Again, where you did not get the error every time, you may need to monitor it's progress to see if the error returns.Second, physically check all cabling. I hope you are not expecting a reply from that poster.Why don't you use one of the forum links in the left hand column to go to an appropriate forum and View all 24 comments Report gw2250- Feb 17, 2009 09:57AM i bought a computer from my grandma she had the computer for 2 years but the software was all messed up The Disk Media Is Not Recognized Floppy Restart the computer, If the computer wont boot from the floppy disk, then it is probably because the boot sequence has been changed, which is why you may get the error

You can also skip that step and just go to the system Bios to check the CMOS settings for start up. Floppy Disk Drive Problems on the Floppy Drive you have the Cable on the wrong way. Memory module. Updating didn't generate any change, but I'm wondering whether "un-installing" (then re-installing again) the driver will have any effect on the error message at "Startup." 2.

Diskette drive. Floppy Disk Driver Windows 7 Find the hard drive, unplug the blue IDE cable and then the power cord that connects to the hard drive. Hard Disk(s) failure (40) HDD controller diagnostics failed. Thanks!

Floppy Disk Drive Problems

Report David- Jan 8, 2009 03:51PM I have the same problem. Memory Verify Error at ... Floppy Disk Problems And Solutions And that can happen after a cool night if the battery is on it's way out. How To Read A Floppy Disk Without Formatting It It has a message saying reboot an solution More resources Read discussions in other Storage categories Hard Drives DVD Drives DVD Writers Optical Media Flash Media NAS/RAID SSD Western Digital Ask

If you are running Windows 3.x click File and click Exit Windows to get to an MS-DOS prompt. check over here The drive may be damaged. Report HOBBY- Apr 29, 2010 08:14AM I JUST RAN INTO THIS PROBLEM ALSO AND TRIED THIS STEP BY STEP AND IT WORKED , SO GLAD BECAUSE IT WAS GETTING TO BE Preview post Submit post Cancel post You are reporting the following post: Disk boot failure: What is it and what can I do to resolve it This post has been flagged Floppy Disk Format Error

Load default settings in Setup. 1783 2. The printer is turned off or unavailable. That should do it at least it did it for me. his comment is here Secondary slave hard disk 3.

Make sure the DIMMs are inserted properly. Floppy Drive Not Working Invalid drive specification - Verify that you floppy drive is setup properly in CMOS Setup. If the same data cable was used for several years(or even the same one across several computers), then it might me the causeĀ of periodicĀ read/write errors that can affect the loading process.

As a last resort (short of opening up the hard drive, that is), could an expert duplicate this: If pressing (is it F8 or F2?) brings up the >Bios/Cmos Set-Up, find

Also when replacing the battery make sure you are using one hand to hold a metal part of your computer case or have an electrostatic wrist strap on to avoid electrostatic Ensure that the diskette/CD-drive subsystem is properly installed. Exception error 12 DOS does not have enough room to handle hardware interrupts. Floppy Disk Not Recognized Insert a system diskette into diskette drive and reboot system.

Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended. Memory parity Error at ... Table 3.1 Common Configuration Error Codes After the beep tone has been produced in the startup sequence, the system shifts over to the process of booting up and begins looking for weblink System board.

Jul 14, 2009 09:19PM i'm really2 thanks to you.......:p lalalalalalalalalalalala........... Keyboard error or 2. do not bother trying to backup your programs because generally they need to be installed not just copied back.3. Is it a key on the keyboard?

Then very important one like many guys mentioned above me go to INTEGRATED DEVICES. Flag Permalink Reply This was helpful (0) Collapse - Re: Disk boot failure by edgar_0587 / July 27, 2007 2:58 PM PDT In reply to: Disk boot failure: What is it If any of the steps on the HP forums resemble those suggested above and have already been attempted, the issue may well point to the disk itself. The floppy disk drive is generating an error message when turning on the PC.

The error code 40 is what I get during the boot up post process. Your advice to someone else was: "I had the same bother and it was enabling floppy disc drive which I dont have.go to bios f2 and click on load default then Symptom 1: "Disk Boot Failure" error screen on startup Every time a computer is turned on, as part of the boot process the BIOS tries to find a bootable drive to These components work together with the device to allocate system resources for the device.

Report markishere2000- Jun 15, 2010 08:39AM can anybody help I am having the same problem but there is no ps2 conections on the back only usb but the usb dont kick Helpful +1 Report afiz..... It is usually necessary to access the system's CMOS setup utility in the following three situations: When the system is first constructed. It took care of my "diskette drive 0 seek failure" problem.

Kozierok.All Rights Reserved. If I press f1 key, everything works fine, but the process continues everytime I start up.