Fisher Paykel Washing Machine Fault Codes
Check connections between the Display Module and the Motor Controller 3. Loading...Oops :Please try again. Primary Source: Wiring. Action: 1. http://epssecurenet.com/fisher-and/fisher-and-paykel-washing-machine-fault-codes.html
The most likely cause of this fault is that the pressure sensor hose has been severed or fallen off during agitate. The Motor Controller module continues to check for 2 minutes, after which time it displays this fault. DETAILED FAULT CODES DETAILED FAULT CODES FOR MODELS Phase 1 GW500 GW600 GW700 GW050 GW060 GW070 GW650 Phase 2 GW701 GW601 GW501 MW051 W015 MW061 MW071 Phase 3 GW703 GW603 GW503 Action: If the water valves are on continuously, check that the water valves turn off mechanically (remove power from machine).
Fisher Paykel Washing Machine Fault Codes
Primary Source: 12 way Harness Connection. Action: 1. Secondary Source: Lid Lock has failed to be activated. - 42 - 192. 230. 231. 232. 233. 234. 517765 March 2004 Action: Replace Lid Lock housing. Fisher And Paykel 00000011 Read the info under error code 00100101.
What does this mean fills okay, but wont agitate, will spin if put into spin mode Sharleen December 2010 my f/p washer the 3 rd light and 4th light [ green Fisher And Paykel 10000010 Action Phase 4 Series 8, Phase 5 Series 9 & Phase 6 Series 11: Reselect the size of the machine by using the SIZE SETTING MODE. I have attached the official version of what Fisher Paykel says about a 130 fault code.. (10000010) Phase 1 to 6 Single Rotor Position Sensor ErrorThe Motor Controller has found an IW Quick Reference Guide . .
Action: Turn the power off at the machine but leave the power on at the wall, then measure the voltage across the terminals of the wax actuator, if a reading of Fisher And Paykel Smart Drive Washing Machine Fault Codes Action: Replace Motor Controller module. 58. And download the parts manual from here: http://www.stokesap.com.au/Manufacturer_Info/FP/WASHERS_DRYERS/517751%20Washers%20Ph%206%20MW511,MWC11,GW511,611,711,IW511,711,811.pdf This manual shows the exploded diagrams so you can see the pump detail. Primary Source: Display Module Phase 1,2 & 3.
- Kategorie Praktische Tipps & Styling Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen...
- Hinzufügen Möchtest du dieses Video später noch einmal ansehen?
- Fault 59. (00111011) Phase 4 to 5 - I D Out of Range Fault When the pause or delay start is pressed to start the machine, the Display checked the physical
Fisher And Paykel 10000010
Mend it How can I mend my Fiat Brava? You may need a service person. Fisher Paykel Washing Machine Fault Codes The 3rd green led light is lit up(wash), the orange led(rinse) and the red (spin) one. Fisher And Paykel 00110001 For Phase 5 Smart Drives the nominal resistance should be approximately 32 ohms.
Check connections of the 12 way harness for bad contacts, corrosion etc. 2. Action: Replace Motor Controller module. (00000100) Phase 1 - Communications Fault The Motor Controller has had difficulty communicating with the Display Module Primary Source: Motor Controller module. Household Appliances, Sewing MachinesHousehold Appliances, StairliftsHousehold Appliances, Steam CleanersHousehold Appliances, Steam IronsHousehold Appliances, Tumble Dryers Full list ... Check This Out Click here for Kenwood repair information.
If you are referring to the lights that are on from diagnostics mode Question about GWL11 Top Load Washer 1 Answer Hi I can't seem to find out what my fault Fisher And Paykel 00100101 Question about GWL11 Top Load Washer 1 Answer Mw511 fault code mw511 fault code pump cuts out on and off and then stops and two LEDS flash with the beep sound Action: Check the continuity of the motor harness and that the connectors are correctly applied to the motor and Motor Controller module.
Check if this device has been activated.
Wähle deine Sprache aus. Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen... I would inspect the wiring after removing the cover before I removed the 4 screws. Fisher And Paykel Washing Machine Error Code 37 Secondary Source:Motor Controller module.
Action: Replace Motor Controller module. (11100110) Phase 6 - EEPROM Value out of Range Wrong version detected Primary Fault: Motor controller is the wrong version Action: Change motor controller (11100111) Phase Replace the stator. Chris August 2014 Just bought a 2nd hand machine. this contact form Action: Turn off Smartdrive at the wall and back on again after 5 seconds.
Your pump could be ... Primary Source: Display Module. Experienced on both high end and regular appliances. 15929851 Type Your Appliance Question Here...