Home > Fisher And > Fisher And Paykel Washing Machine Fault Codes

Fisher And Paykel Washing Machine Fault Codes

Contents

The absence of a fault code points toward a user warning and I would be suspicious of the balance switch. http://applianceguru.com/forum2/1816.html ____________________please help us to help you, http://www.fixitnow.com/beerfund.htm Back To Top PM Quote Reply Posted: Mon Aug 15th, 2005 11:43 am PM Quote Reply 9th Post ethicalfix Joined:Wed Jul I think it is from a bad seal on the pump shaft allowing water to leak on to the pump motor. it seems to fill with water and then stop & beep-don't think it is agitating! http://epssecurenet.com/fisher-and/fisher-paykel-washing-machine-fault-codes.html

It is easier to try and figure out from a picture what it looked like than to try and remember. It has a fan blade hanging from the bottom of it. Anzeige Autoplay Wenn Autoplay aktiviert ist, wird die Wiedergabe automatisch mit einem der aktuellen Videovorschläge fortgesetzt. Anyway, what's your take?

Fisher And Paykel Washing Machine Fault Codes

do I bookmark this current url thread to get back to you? I tried that too. Thanks

Question?

Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Tilt the machine back and let it rest on the wall. I checked diverter valve & pump for blockages and found no problem. Fisher And Paykel Washing Machine Diagnostic Mode If the blade does spin freely, there is a "Y-connection" in the back right corner with (3) 1" hoses connected to it.

Getting the part The easiest way to find the model part number for the controller module is to open the panel. Fisher And Paykel 10000010 Fisher Paykel washer repair is simple, we know these units well and can assist you with any repair or review question you have. This is a pump block error. Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar.

An alternative move would be to test the machine with the restart function turned off. Fisher And Paykel 00100101 Ask Your Own Australia Whitegoods Question Customer: replied4 years ago. I removed two good 31J diodes, tested them and found that they
were just regular diodes with high reverse voltage, Vr.

A test run revealed that the water
temp sensor grommet failed and You mentioned the water pump was making bearing noises.

  1. Is diode D126 a 5.1 v zener?
  2. I took the hose off at each end end blew through it and it is working again today.
  3. It is giving you a code and telling you what the problem is within itself.
  4. Just make certain that everything connects as it did before (use the pictures you took before to double check).
  5. Sorry been away.
  6. Kategorie Praktische Tipps & Styling Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen...
  7. Is this repairable or must the board be replaced?
  8. In my case the machine will not work.
  9. Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help
  10. Remove any blockages if necessary.

Fisher And Paykel 10000010

Link from earlier. Make sure you not which hoses go on which outlet of the y-connection because you will need to re-install it. Fisher And Paykel Washing Machine Fault Codes So I thought I'd write up what I did. Fisher And Paykel Smart Drive Washing Machine Fault Codes That is, keep the angle the same as the module sits in.

If unsure how to put it back together, just take a picture of how it looks before you start. his comment is here How do I come back to you later to complete this? Expert: Tyler Z. During the repair, always double check and take a look at that plug to make sure it is off the wall before doing anything inside the machine. When the thermal device has reset, the module will power up normally. Fisher And Paykel 00110001

Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. Machine can be spinning and filling with water and be quiet, then suddenly start screeching for a while. To find the error code, turn the machine on by holding down the pause button button and pressing the power button on the top of the machine. this contact form and post back. ____________________please help us to help you, http://www.fixitnow.com/beerfund.htm Back To Top PM Quote Reply Posted: Sat Aug 13th, 2005 12:28 am PM Quote Reply 5th Post Marcntyme Grasshopper

I'll be helping you with your problem today.Lets see if an error code pulls up. How To Reset Fisher And Paykel Washing Machine Thanks Tania Submitted: 4 years ago. The model number of the controller module (421297NAP) can be clearly seen in this picture.

Select a lower wash temperature.

They said they didn't have the item in stock, but I received the module the following day anyway using express post. (I don't know anyone who works there or anything like Any suggestions?

Thanks

Ed

Help! Fisher Paykel washer have one very common error code. Fisher And Paykel Washing Machine Not Spinning Turn on the washing machine normally.

Marcntyme Back To Top PM Quote Reply Posted: Mon Aug 15th, 2005 11:32 am PM Quote Reply 8th Post Kiwi-nadian Joined:Tue May 24th, 2005 Location:Cowtown, Alberta Canada Posts:376 Flavorite It should be easy now to remove the right hand side. been a minute since I have actually walked someone through itRepairman1981 : there is a up and a down arrow on the wash temp sectionRepairman1981 : yes the up arrowCustomer: just navigate here I felt that at least I should give the repair a go.

How to test which is bad.? We replaced the control module, pump, and the diverter. The flow rate of the supply water is too slow. That is, start the machine by holding water temp down.

Thanks.

Where can I get a fuse for my washer control board
478089USP? If you're sharing your DIY project, please tell us how you did it. So if your machine isn't in the manual, don't worry. 2 commentsshareall 2 commentssorted by: besttopnewcontroversialoldrandomq&alive (beta)[–]aggie94 1 point2 points3 points 1 year ago(1 child)Nice information! The two connections that looked the most difficult, were actually the easiest.

replied4 years ago. Cold water temperature exceeds recommended limits (see 'Installation instructions' , page 4). If you're asking for help, please give details. Please see above.

Look for the pump (it has hoses connected to it and 2 separate plug in wire points), The hoses come off easy by squeezing the spring retainer clip and the wires The most useful information found was a copy of the service manual (attached) with a listing of the fault codes, but no reference to the Control Module or its schematic.