Home > Fisher And > Fisher And Paykel Error F31

Fisher And Paykel Error F31

Solution Ensure the Child Lock function is off. make sure there is no plug in the filter. Primary Action - Check sensor connection at controller. When we take the filter off and press the button on the door the water comes through but not with the filter... have a peek here

Fault 4 PC SENSOR RESISTANCE FAULT The resistance of the PC Sensor is outside of the normal range (> 45k ohms). Solution Minimise door openings to allow the refrigerator temperature to stabilise. by Joey S Earned 73,355 community points in Click'>Appliances December 26th, 2008 Comment Give your feedback by voting on answers 1 votes Didn't find what you are looking for? All rights reserved.

What does the code F10 indicate for service? 2 answers Popular Products in Frigidaire Frigidaire FFEW2725PW 27" Electric Single Wall ... Solution The DishDrawer™ is overloaded. Water stops. 6.

If the ambient sensor is faulty the electronic module will have to be replaced. Solution The oven door will unlock when it has cooled to a safe temperature. Possible Cause The spray arm holes are blocked. If Code 7 re-appears recheck for IO faults.

Secondary Action - If there is a short, inspect the harness to trace the short F13 Over Temperature If the exhaust air temperature is above 90 degrees C a fault is The DishDrawer™ is leaking water Possible Cause The drain hose has disconnected from the waste pipe. Either the heater or wiring is faulty. Secondary Action - Check fan.

The support line says this is a display fault. If not within limits replace heater. Sounds like it's come off the rails, empty it completely trays & all. Solution Dry the detergent dispenser before loading again to prevent caking.

The DishDrawer™ is making excessive motor noise Possible Cause The filter plate/spray arm is incorrectly placed. Solution Ceramic cleaner should remove the marks. Check the wiring and connections at the solenoid and the module. Hide thumbs Also See for E522BLXU Supplemental service manual - 45 pages 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Primary Action - Check FC fan wiring and connections at both the fan and power module. navigate here Browse Categories Answer Questions Fisher and Paykel Refrigerator Refrigerators All Unanswered Join Sign In Ask a Question × HomeForumRefrigeratorsFisher and PaykelFisher and Paykel... Its best handled by a Technician but you could possibly do it by taking your model number to the nearest appliance parts store and asking for the parts. it sounds like when u install the filter thewater tube is not engaging in the filter.

  1. Contributor 1 Answer Re: Fisher and Paykel RF201ADUX Refrigerator - error code...
  2. Fault 13 FC FAN CURRENT HIGH CURRENT FAULT The FC fan is drawing more current than expected.
  3. Solution The DishDrawer™ is overloaded or loaded incorrectly.
  4. If it is only two years old I would suggest you contact F&P Customer Care on 1.888.936.7872This is a known issue and I doubt they would argue if you asked them
  5. The food inside the refrigerator is freezing Possible Cause Food has been placed directly in front of air outlets (Active Smart models only).
  6. Active Smart Stage 4.2 Fault 1 POWER/CONTROL MODULE SELF TEST FAULT On the last poer up, the Power/Control module failedits self test.
  7. Fault 7 Stage 1,2,3 NO FAULT If this LED is flashing the cabinat is either a stage 4 cabinet or the cabinet is not displaying fault.
  8. See Details More Products Frigidaire FGMC2765PB Gallery 3.8 cu.

Solution Ensure the spray arm is able to rotate. Or just drag it here! Solution Select a lower water level for smaller wash loads. Check This Out Solution Move items in the freezer so the door can close tightly.

Solution Wipe outside surface dry. Either the wiring is open circuit or the fan is faulty. Primary Action - Unplug the exhaust sensor and check the resistance.

Replace the exhaust sensor if faulty.

Fault 18 FC FAN CURRENT HIGH CURRENT FAULT The FC fan is drawing more current than expected. Primary Action - Check 6 way sensor RAST connector at Power/Control module. Primary Action - Check the 6 way Fan'LAH RAST connector at Power/Control module. Fault 5 FC SENSOR RESISTANCE FAULT The resistance of the FC Sensor is outside of the normal range (> 45k ohms).

Category:Appliance Share this conversation Expert: Appliance Tech Larry replied6 years ago. Fault 7 POWER/CONTROL MODULE SELF TEST FAULT On the last poer up, the Power/Control module failedits self test. Dispense water. 2. this contact form We hope it helps solve your problem.

This fridge is 2 years old! I'd still really like to see a copy of the service manual if you would be okay to post it.JD Expert: FPTech replied4 years ago. Also causing the frezzer to ice... Tell us some more!

Solution Choose a standard wash programme. If faulty, replace. Code F30 No display signal received (shorted or broken wire). Ask Appliance Tech Larry Your Own Question Appliance Tech Larry, Home Appliance tech Category: Appliance Satisfied Customers: 19183 Experience: Over 35 years of in home appliance repair and service 14308609 Type

Solution Select the PERMANENT PRESS or CREASABLES option as this will select a slower, shorter spin speed. F34 Both Solenoid Drivers have failed. Fault 17 FC FAN CURRENT LOW CURRENT FAULT The FC fan is drawing less current than expected. Secondary Action - Replace sensor.

Check resistance of sensor. Ask a Question Request a Manual Ask A Question Request A Manual Sponsored Listings Loading Products... Error code F31 on your Fisher & Paykel means no display signal, short/broken wire. The machine is continuously filling Possible Cause The machine is siphoning.

Primary Action - Check FC fan wiring and connections at both the fan and power module. Generated Sat, 15 Oct 2016 20:00:24 GMT by s_ac15 (squid/3.5.20)